Analysis of Quality Control Using the Failure Mode And Effect Analysis (FMEA) Method in the Welding Process in the Feed Drum Project

Rizkia Maulindah Lisna, Efta Dhartikasari Priyana, Hidayat Hidayat

Abstract


PT. Xyz is a steel fabrication company located in Gresik. One of their  projects undertaken by PT. XYZ is a Feed drum Project, the welding process is the most important stage in this project. At the time of product testing or testing there were still many welding points that were defective so that the product did not pass the trial, the trial was carried out by hydrotest where this test was carried out with water as the test medium to determine the strength of a material and find out whether there was a leak or not and as well as a visual check. The types of defects found in the feed drum project are spatter, overlap, porosity, undercut, incomplete fusion, slag, bad String Bead (Weaving Fault), start stop, pin hole. The research uses the FMEA (Failure Mode Effects and Analysis) the method which aims to identify and analyze the occurrence of defects. In the results, the highest RPN value is found in the Incomplate Fusion type of defect with a value of 384 so that it becomes a priority in carrying out control and repair .


Full Text:

PDF

References


R. Ratnadi and E. Suprianto, “Pengendalian Kualitas Produksi Menggunakan Alat Bantu Statistik (Seven Tools) Dalam Upaya Menekan Tingkat Kerusakan Produk,” J. Indept, vol. 6, no. 2, p. 11, 2016, [Online]. Available: https://jurnal.unnur.ac.id/index.php/indept/article/view/178/0.

J. Hardono, H. Pratama, and A. Friyatna, “Analisis Cacat Produk Green Tyre dengan Pendekatan Seven Tools,” J. INTECH Tek. Ind. Univ. Serang Raya, vol. 5, no. 1, p. 1, 2019, doi: 10.30656/intech.v5i1.1462.

Z. Fatoni, M. L. King, and M. Lazim, “Perencanaan Desain Alat Bantu Temporary Clamp 8" Pada Pipe Line Industri Migas,” J. Desiminasi Teknol., vol. 9, 2021.

R. Y. Pratama, M. Basuki, and E. Pranata, “Pengaruh variasi arus pengelasan smaw untuk posisi pengelasan 1g pada material baja kapal ss 400 terhadap cacat pengelasan,” Jur. Tek. Perkapalan FTMK-ITATS, vol. 02, no. 1, pp. 203–209, 2020.

A. Khatammi and A. R. Wasiur, “Analisis Kecacatan Produk Pada Hasil Pengelasan Dengan Menggunakan Metode FMEA (Failure Mode Effect Analysis),” J. Serambi Eng., vol. 7, no. 2, pp. 2922–2928, 2022, doi: 10.32672/jse.v7i2.3853.

W. S. Nugroho, “Memperbaiki Hasil Pengelasan,” Buku Inf., pp. 1–67, 2018.

B. Septiana and B. Purwanggono, “Analisis Pengendalian Kualitas Dengan Menggunakan Failure Mode Error Analysis (Fmea) Pada Divisi Sewing Pt Pisma Garment Indo,” Ejournal3.Undip.Ac.Id, 2018, [Online]. Available: https://ejournal3.undip.ac.id/index.php/ieoj/article/view/22233.

Y. A. Fauzi and H. Aulawi, “Analisis Pengendalian Kualitas Produk Peci Jenis Overset Yang Cacat Di Pd. Panduan Illahi Dengan Menggunakan Metode Fault Tree Analysis (Fta) Dan Metode Failure Mode and Effect Analysis (Fmea)”,” J. Kalibr., vol. 14, no. 1, pp. 29–34, 2016, doi: 10.33364/kalibrasi/v.14-1.331.

A. Rahman, “Analisis Pengendalian Kualitas Produk Roti Tawar Mr . Bread Dengan Metode FMEA ( Di Bagian Produksi CV . Essen ),” J. Online Tek. Ind., vol. 1, no. 1, pp. 1–8, 2014.

M. Basori and S. Supriyadi, “Analisis Pengendalian Kualitas Cetakan Packaging Dengan Metode Failure Mode and Effect Analysis (FMEA),” Pros. Semin. Nas. Ris. Ter. SENASSET, pp. 158–163, 2017, [Online]. Available: https://e-jurnal.lppmunsera.org/index.php/senasset/article/view/442.

A. Wibowo, “Macam-Macam Cacat Las,” Macam Cacat Las, no. 109511414319, pp. 1–9, 2016.




DOI: http://dx.doi.org/10.24014/sitekin.v20i2.21731

Refbacks

  • There are currently no refbacks.


Copyright (c) 2023 SITEKIN: Jurnal Sains, Teknologi dan Industri



Editorial Address:
FAKULTAS SAINS DAN TEKNOLOGI
UIN SULTAN SYARIF KASIM RIAU
Kampus Raja Ali Haji
Gedung Fakultas Sains & Teknologi UIN Suska Riau
Jl.H.R.Soebrantas No.155 KM 18 Simpang Baru Panam, Pekanbaru 28293
Email: sitekin@uin-suska.ac.id
© 2023 SITEKIN, ISSN 2407-0939

SITEKIN Journal Indexing:

Google Scholar | Garuda | Moraref | IndexCopernicus | SINTA


Creative Commons License
SITEKIN by http://ejournal.uin-suska.ac.id/index.php