Decision Making in Selecting Plywood Suppliers at PT Papan Dekorasi Using the Analytical Hierarchy Process (AHP) Method

Ima Rohimah, Winarno Winarno

Abstract


The proper selection of suppliers is a crucial factor in the manufacturing industry as it significantly influences production efficiency and the quality of final products. PT Techno Wood Indonesia, a company engaged in the production of decorative panels, highly depends on high-quality plywood as its main raw material. This study applies the Analytical Hierarchy Process (AHP) method to determine the best plywood supplier based on relevant criteria. Data were collected through observation, interviews, documentation, and questionnaires distributed to the Purchasing/Procurement staff, supported by secondary data from company documents and literature. The results indicate four main criteria with the following weights: Performance (0.537), Quality (0.271), Cost (0.131), and Responsiveness (0.061). From the global priority synthesis, PT Sumitomo Forestry ranked first with a weight of 0.476, followed by PT SMB Gobel Indonesia (0.362) and PT Itochu Indonesia IDR (0.162). These findings highlight that PT Techno Wood Indonesia prioritizes performance and quality over cost and responsiveness, with PT Sumitomo Forestry identified as the primary plywood supplier.


Full Text:

PDF

References


P. Citra and I. W. Sriyasa, “Analisis Pemilihan Pemasok Bahan Baku Menggunakan Metode Rank Order Centroid dan SMART,” J. Artif. Intell. Technol. Inf., vol. 2, no. 3, pp. 153–162, 2024.

K. Budhy Luhur, “Pengaruh Kualitas Produk terhadap Pemilihan Vendor di PT. Hitachi Power Systems Indonesia,” 2020.

I. Jones, “Pengaruh Manajemen Rantai Pasokan Sistem ERP dalam Meningkatkan Kinerja Perusahaan (Studi Kasus: PT Latinusa TBK),” J. Ekon. dan Bisnis, vol. 10, no. 2, 2022.

E. Susanti and R. Rusdah, “Pemilihan Supplier Pada Apotek Pusaka Arta Dengan Metode Analytical Hierarchy Process (AHP) dan Simple Additive Weighting (SAW),” IDEALIS Indones. J. Inf. Syst., vol. 3, no. 1, pp. 405–410, 2020, doi: 10.36080/idealis.v3i1.1954.

D. Dahriansah, A. Nata, and I. R. Harahap, “Sistem Pendukung Keputusan Pemilihan Siswa Berprestasi Pada Aliyah Aras Kabu Agung Tanjungbalai Menggunakan Metode AHP,” J-SISKO TECH (Jurnal Teknol. Sist. Inf. dan Sist. Komput. TGD), vol. 3, no. 1, p. 86, 2020, doi: 10.53513/jsk.v3i1.199.

R. A. Alatas, A. Putri, and T. Subroto, “Application of Quality Function Deployment (QFD) Method in Developing Eco-Friendly Cup Holder Design,” J. Ris. Ilmu Tek., vol. 3, no. 1, pp. 44–55, 2025.

V. F. Gurning, Y. Bernat, G. Adiyat, and Kusri, “Strengthening Institutions and Governance in the Palm Oil Sector for Smallholder Empowerment: A Soft-Structural-Analytical Systems Model,” J. Ris. Ilmu Tek., vol. 3, no. 2, pp. 68–85, 2025.

M. Akbar, C. Guterres, and A. Araujo, “A Backpropagation-Based Artificial Neural Network Model for Predicting Pharmaceutical Demand,” J. Ris. Ilmu Tek., vol. 3, no. 1, pp. 1–15, 2025.

H. Suherman, R. Rodiah, and D. Pitoyo, “Pendekatan Metode Analytical Hierachy Process (AHP) untuk Menentukan Supplier Kain di Konveksi YZ Production,” Rekayasa Ind. dan Mesin, vol. 5, no. 1, p. 19, 2023, doi: 10.32897/retims.2023.5.1.1986.

F. Ahmad, N. Syauqi B N, D. Kurniawan, and T. A. Pamungkas, “Analisis Pemilihan Supplier Menggunakan Metode Analytical Hierarchy Process (AHP) pada Industri Ritel Sepatu,” J. Teknol. dan Manaj. Ind. Terap., vol. 4, no. I, pp. 45–51, 2025, doi: 10.55826/jtmit.v4iI.469.

P. S. Felicia and N. Zaitun, “Design a Patient Medical Record Application to Shorten Registration Time Using the Waterfall Model,” J. Ris. Ilmu Tek., vol. 1, no. 2, pp. 62–77, 2023.

R. Ravsanjani, F. Raji, and M. Salahuddin, “Redesign the Wood Cutting Saw to Be More Ergonomic Using The TRIZ Method,” J. Ris. Ilmu Tek., vol. 1, no. 3, pp. 175–185, 2023.

H. Kamil, M. Mukhlis, and Y. Bachtiar, “Integration of ANP and TOPSIS Methods in Prioritizing Sales Strategies for Frozen Food Products,” J. Ris. Ilmu Tek., vol. 1, no. 2, pp. 102–114, 2023.

“Optimizing Hospital Pharmaceutical Warehouse Operations Using Discrete Event Simulation”.

R. Erwanda, “Layout Design of Copra Factory Facilities in Small and Medium Industry Centers Using Systematic Layout Planning Method,” J. Ris. Ilmu Tek., vol. 1, no. 2, pp. 115–127, 2023.

“A Hybrid Six Sigma DMAIC and Fuzzy-FMEA Framework for Defect Reduction and Quality Enhancement in White Copra Production”.

G. Bakioglu, “AHP integrated TOPSIS and VIKOR methods with Pythagorean fuzzy sets to prioritize risks in self-driving vehicles,” Appl. Soft Comput., vol. 99, 2021, doi: 10.1016/j.asoc.2020.106948.

B. Wang, “Selecting sustainable energy conversion technologies for agricultural residues: A fuzzy AHP-VIKOR based prioritization from life cycle perspective,” Resour. Conserv. Recycl., vol. 142, pp. 78–87, 2019, doi: 10.1016/j.resconrec.2018.11.011.

I. Konstantinos, “A Decision Support System methodology for selecting wind farm installation locations using AHP and TOPSIS: Case study in Eastern Macedonia and Thrace region, Greece,” Energy Policy, vol. 132, pp. 232–246, 2019, doi: 10.1016/j.enpol.2019.05.020.

H. Boudlaie, “Designing a human resource scorecard: An empirical stakeholder-based study with a company culture perspective,” J. Entrep. Manag. Innov., vol. 16, no. 4, pp. 113–147, 2020, doi: 10.7341/20201644.

C. Ren, “Integrated multi-objective stochastic fuzzy programming and AHP method for agricultural water and land optimization allocation under multiple uncertainties,” J. Clean. Prod., vol. 210, pp. 12–24, 2019, doi: 10.1016/j.jclepro.2018.10.348.

M. F. Ak, “AHP–TOPSIS integration extended with Pythagorean fuzzy sets for information security risk analysis,” Complex Intell. Syst., vol. 5, no. 2, pp. 113–126, 2019, doi: 10.1007/s40747-018-0087-7.

Tengku Khoirunnisa, Chellcia Mutiara Iwfanka, and Melkisedek Gumi, “A Taguchi-Based Framework for Continuous Quality Improvement in Crude Palm Oil Production ,” J. Ris. Ilmu Tek., vol. 2, no. 3 SE-Articles, pp. 143–154, Dec. 2024, doi: 10.59976/jurit.v2i3.134.

B. A. and H. Haiban, “Synergistic Effects of Gypsum and Cement on the Geotechnical Properties of Clay Soils: Experimental Evaluation of CBR, UCS, and Compaction Characteristics”.

“Decision Support System Model for PPPK Teacher Selection Using the AHP Method”.

“Integrating Quality Function Deployment (QFD) in the Hygienic Oil-Draining Tools for MSMEs: A Consumer-Centered Approach”.

Devi Puspitata Sari, Lei Hou, and Zong Woo Geem, “Backpropagation Neural Network Model for Predicting Spare Parts Demand Under Dynamic Industrial Conditions,” J. Ris. Ilmu Tek., vol. 2, no. 3 SE-Articles, pp. 129–142, Dec. 2024, doi: 10.59976/jurit.v2i3.124.

I. N. Permadi and D. B. Nisa, “A Model Experiment Design Using the Taguchi Method: A Case Study Of Making Concrete Roof,” J. Ris. Ilmu Tek., vol. 1, no. 1, pp. 36–44, 2023.

I. Eliona and D. Ranova, “Systematic Diagnosis of Quality Defects in Concrete Electricity Poles Through the New Seven Tools,” J. Ris. Ilmu Tek., vol. 2, no. 3, 2024.

C. Anisa and R. Rahmatullah, “Visi Dan Misi Menurut Fred R. David Perspektif Pendidikan Islam,” J. Eval., vol. 4, no. 1, p. 70, 2020, doi: 10.32478/evaluasi.v4i1.356.

M. Rajak, “Evaluation and selection of mobile health (mHealth) applications using AHP and fuzzy TOPSIS,” Technol. Soc., vol. 59, 2019, doi: 10.1016/j.techsoc.2019.101186.

T. Saranya, “Groundwater potential zone mapping using analytical hierarchy process (AHP) and GIS for Kancheepuram District, Tamilnadu, India,” Model. Earth Syst. Environ., vol. 6, no. 2, pp. 1105–1122, 2020, doi: 10.1007/s40808-020-00744-7.

P. Arulbalaji, “GIS and AHP Techniques Based Delineation of Groundwater Potential Zones: a case study from Southern Western Ghats, India,” Sci. Rep., vol. 9, no. 1, 2019, doi: 10.1038/s41598-019-38567-x.

M. Yucesan, “Hospital service quality evaluation: an integrated model based on Pythagorean fuzzy AHP and fuzzy TOPSIS,” Soft Comput., vol. 24, no. 5, pp. 3237–3255, 2020, doi: 10.1007/s00500-019-04084-2.

Ahmad, “Performance analysis of employees at Pt. Sungaiberkat serani sukses using human resource scorecard method,” 2020. doi: 10.1088/1757-899X/852/1/012119.

M. Bakir, “Application of fuzzy ahp and fuzzy marcos approach for the evaluation of e-service quality in the airline industry,” Decis. Mak. Appl. Manag. Eng., vol. 4, no. 1, pp. 127–152, 2021, doi: 10.31181/dmame2104127b.

A. Calabrese, “Integrating sustainability into strategic decision-making: A fuzzy AHP method for the selection of relevant sustainability issues,” Technol. Forecast. Soc. Change, vol. 139, pp. 155–168, 2019, doi: 10.1016/j.techfore.2018.11.005.

A. S. Habibullah and S. A. Sianipar, “Sustainable GSM-Based Remote Switching System Using Conventional Mobile Phones Without Microcontroller for Low-Cost Automation Applications,” J. Ris. Ilmu Tek., vol. 2, no. 3, 2024.

A. Awaludin and N. Nazaruddin, “Fuel Distribution Route Optimization Model Based on Hybrid Cheapest Insertion–Tabu Search,” J. Ris. Ilmu Tek., vol. 3, no. 1, pp. 56–67, 2025.

G. P. Samitra, C. Setiawan, and J. Siman, “Design and Build a Cassava Peeling Machine to Increase Productivity,” J. Ris. Ilmu Tek., vol. 1, no. 3, pp. 128–138, 2023.

D. Fitriani, R. Nasution, and N. Sari, “Productivity Analysis on Liquid Nitrogen (LIN) and Liquid Oxygen (LOX) Production Using Objective Matrix (OMAX) Method,” J. Ris. Ilmu Tek., vol. 1, no. 3, pp. 139–150, 2023.

“A Decision Support System for Evaluation Service Quality by Fuzzy SERVQUAL: A Case Study of a Modern Retail.”

M. A. Eduardo, E. Carlojay, J. Tomaic, and Ramirez, “Experimental Analysis of the Effect of Valve Clearance Variations on the Performance and Emissions of Suzuki G15A Gasoline Engines in the Philippines,” J. Ris. Ilmu Tek., vol. 3, no. 1, pp. 16–29, 2025.

F. A. Alaba, A. Nyakubu, O. Oluwajana, B. Abafemi, and O. Adewale, “Evaluating Based E-Learning Platforms in Nigerian Higher Education: An SEM-PLS Analysis Based on the DeLone and McLean Model,” J. Ris. Ilmu Tek., vol. 3, no. 1, pp. 30–43, 2025.

K. A. Rene, V. Velupessy, and C. Obediencia, “Hybrid Fuzzy–Eckenrode Model for Quantitative Evaluation of Fermented Cocoa Bean Quality in Ivory Coast,” J. Ris. Ilmu Tek., vol. 3, no. 2, pp. 86–99, 2025.

S. N. Yodipjit, S. Wangrakdiskul, N. Charoensuk, K. Phromphat, and C. Boonmee, “Sustainable Quality Transformation in Agro-Industrial Manufacturing: A Six Sigma–Kaizen Model for Thailand’s Crude Palm Oil Sector,” J. Ris. Ilmu Tek., vol. 3, no. 2, pp. 125–140, 2025.

A. D. Selvitre, Y. Yeni, and P. Keswardi, “Analysis of Prestress Loss and Structural Performance of Box-Type Prestressed Concrete Girders on the Cakung Flyover,” J. Ris. Ilmu Tek., vol. 3, no. 2, pp. 100–111, 2025.

V. Z. Mutiara and E. Syah, “Forecasting-Inventory Optimization Model: Integrating Exponential Smoothing with Min-Max and Blanket Order Systems for SMEs,” J. Ris. Ilmu Tek., vol. 2, no. 3, pp. 187–197, 2024.




DOI: http://dx.doi.org/10.24014/sitekin.v23i1.38231

Refbacks

  • There are currently no refbacks.


Copyright (c) 2025 SITEKIN: Jurnal Sains, Teknologi dan Industri



Editorial Address:
FAKULTAS SAINS DAN TEKNOLOGI
UIN SULTAN SYARIF KASIM RIAU
Kampus Raja Ali Haji
Gedung Fakultas Sains & Teknologi UIN Suska Riau
Jl.H.R.Soebrantas No.155 KM 18 Simpang Baru Panam, Pekanbaru 28293
Email: sitekin@uin-suska.ac.id
© 2023 SITEKIN, ISSN 2407-0939

SITEKIN Journal Indexing:

Google Scholar | Garuda | Moraref | IndexCopernicus | SINTA


Creative Commons License
SITEKIN by http://ejournal.uin-suska.ac.id/index.php